Latest horticulture pump repair Tenders | Government horticulture pump repair Tenders

State Government

CTN :43467490

16 Jan, 2026 NA

Delhi - Delhi

Tender For corrigendum : s/i/t/c of e/m equipments and allied works for newly re-bored tube well at okhla vihar near majar in okhla constituency ac-54. - supply of submersible pump set fitted with dynamically balanced ss impeller mounted on stainless steel shaft with protection sleeve having stage bowl & closed grained shorted type impeller, the pump will be directly coupled to required wet type induction motor of 7.5 hp, 15 stage, speed 2900 rpm suitable for operation of 3 phase, 415 volt, 50 hz, ac supply with efficiency 70% at following duty point: 200-125-75 lpm on 89-124-133 mtr. head.having discharge outlet 50 mm and outside dia 142 mm.make: bs/skope/ any djb approved. , supply of hut type electrical feeder pillar / fabricated with 50 x 50 x 6mm angle iron and 16 swg ms sheet with horizontal and vertical intermediate member of suitable size. i.e. 1370 mm x 760mm x 460 mm. with arrangement for mounting of switchgear and electrical energy meter i.c. painting heaving following item fitted. a) mccb 63 amp, 4pole, 415volt, 35 ka -1 no. b) rccb 63 amp, 4pole with earth fault indication protecting a circuit automatically in the event of earth leakage sensitivity 100ma, - 1 no c) fully automatic star delta starter of relay range 13-21 amp. (7.5 hp to 10 hp) 3 phase oil immersed type -1 no.d) ampere 96 x 96 mm. square shape 0-30 amp-1 no. e) voltmeter 96 x 96 mm. square shape 0-500 volt-1 no.e) indicating lamp (a set of 3 lamps) 1.setf) shunt capacitor of 10 kvar mpp type with three phase isolator with suitable banking g) motor protection assembly with earth leakage protection phase sequence corrector, single phasing, protection, overload protection, high voltage / low voltage protection time delay power on, programmable time switch i.c. r&b phase facility to change over from automatic, to manual &vice verse for up to 10 h.p -01 nos.complete wiring &installation of above accessories with required copper conductor wire and thimble etc. 01 job.make of all components: any djb approved., s/o pvc insulated and pvc sheathed cable with plain copper conductor having 3 phases, 3 core flat for submersible motor of 4 square mm size each 100 mtrs. make:grandlay / havells./any djb approved make, s/o m.s. clamp of 600 mm length duly fabricated out of 12.5 mm thick 75 mm wide, m.s. plate for holding the pipe of 50 mm dia., s/o double flange gi column pipe 50 mm dia medium class each of 3 mtrs long duly threaded on both ends, welded fitted with gi flange on both ends with slot of submersible cable. make: tata/ jindal./any djb approved make, s/o/ tail piece of the medium class gi pipe 500 mm long with one end threaded as per outlet of pump & another end flanged as per size of gi pipe 50 mm dia., s/o gi 90 bend of size 50 mm dia having both side flange (heavy duty)., supply of ms nut bolts off size as per requirement., s/o rubber packing for 50 mm dia flange., fabrication and supply supply of bore cover approx size 1x1 made out from 6mm thick m.s. sheet in 2 halves and a circular hole in centre 3-1/2 dia. with locking arrangement by nuts and bolt. , earthing with g.i. earth pipe 4.5 meter long, 40 mm dia including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe etc. with charcoal/ coke and salt as required., providing and fixing 6 swg dia g.i. wire on surface or in recess for loop earthing as required., installation of t/well by lowering of sub p/set with all allied above items. this includes installation and grouting of panel boards with all electrical wiring & cabling at site. all tools & tackles i/c. tripod chain pulley blocks etc. shall be arranged by the firm. this includes testing & commissioning of t/well on load at site i/c. cartage, loading & unloading of material. it also includes a trial run of 30 hrs operation successfully by the firm. all required civil work included in the scope of work.

State Government

CTN :43516494

21 Jan, 2026 71.05 Lacs

Kota - Rajasthan

Tender For 15, 7.5 and 5 hp solar pump set with material and installation

State Government

CTN :43536211

17 Jan, 2026 NA

Pathardi - Maharashtra

Tender For supplying material for construction of road at kothawale wasti hapsha pump to daka road at sangavi surya tal- parner

Central Government/Public Sector

CTN :43270629

15 Jan, 2026 NA

Ratlam - Madhya Pradesh

Tender For corrigendum : supply of title - aluminium extension ladder, 11m aluminium ladder extension wall support ladder 24/40 asspecification given below aluminum alloy wall support extension ladder proved with top hand rallis and platform steps made of 26" 3 mm round corrugated flutted pipe main extrusion made up of aluminum alloy section 66*32*4mm thickness of he 30 grade t6 tempe hindalco make closed height 24 feet additional msguide pipe fixed insideheight 40 feet additional msguide pipe fixed inside of the ladder at 1 mir internal for stability of ladder arms., aluminium tower ladder of tiltable (inclined) tower ladder with bucket type having reach height of 31-40 (detailed descripbon/specification as per product # 1of gem contract no. gemc-511687717666536 dt. 15/12/2024) make-alied, alco, sumer, s.j. ladders, aluminium ladder self support & feet, anti skidding make-caw or superior , supply of heavy duty manual drum trolley suitable for handling standard 200-250 liter drums, capacity 250 kg. made of ms with powder-coated finish, suitable for titing, lifting and rotating operations, provided with 3 puirubber wheels for easy movement, equipped with mechanical drum holding damp, rotatable up to 3607, lifting height approx. 300-500 mm, manual handle operated, robust construction, without sharp edges , supply of heavy duty long life hydraulic operated manual stacker as per description: capacity 2000 kg. overall length 17:50 mm, fork arm length 1150 millimeter, overall fork width 650 mm (adjustable), lowered fork height 85 mm, mast height (close height) 2000 mm, tuming radius 1450 mm, lifting speed 14 mm per stroke, tandem pu rollers (80-70 mm), pump made of cast steel with powder-coated finish, construction ms (6 mm), service weight 234 kg, controllable lowering speed, and without sharp edges, supply of heavy duty aluminium, telescopic ladder, 14 steps (approx.) maximum extended height 18 ft (approx.), made of aluminium alloy with 1.5 mm thickness (approx.) foldable design, overall dimensions 109.27 48.57 8.8 cm (all approx.), weight 13.5 kg (approx), load capacity 150 kg (approx.), supply of aluminium platform ladder, height 5 ft (approx.), 4 steps (approx.), load capacity 100 kg (approx.), foldable design with top platform, made of aluminium, robust construction, without sharp edges, light weight moped trolly, push trolley b.g. with umbrella complete for p.way track inspection as per rdso specification no. tm/sm/lw/pt dated 03.02.2014, push trolley b.g. with umbrella complete for p.way track inspection as per rdso specification no. tm/sm/lw/pt dated 03.02.2014, digital cooking oil tester for total polar compounds (tpc meter). sample to be approved by competent authority before supply., poly proplene rope 18mm dia, unbranded pvc flexible waste pipe length 1200 mm brand: na (detailed description/ specification as per product # 1 of gem contract no. gemc-51168776088276 đi. 05/03/2025), upvc column pipe 50 mm dia type "heavy" pressure 27 kg/cm2, item code (colhvy200c) & equivalent. make: kisan kml, ashirwad kasta, retro reflective sticker golden yellow colour size width 4 feet, thick 0.40 to 0.45 mm.for slr brand mor avery dennison or orajet or similar, ss. self drilling screw 19x6 mm,, as per din and isi standard, bib cock as per cat. no. 29037 fusion range of m/s jaquar or mso-2080 of m/s marc, or fno-011 of m/s eauset or hr03 of essess or se-00202 of m/s agmeco, as approved by cde/rcf, subject to compliance of firm with clause 3 to clause 7 of section a of rdso/2008/cg-05, chain pulley block-2 ton chain length 10msingle fall isi marked, chain pulley, material- casting and forging, max lifting height: 3m - 10m, chain length: 3m-10m, weight: 20 kg (for 3m chain). make: ferreterro model number: ll020, indef 2000 kg (2 ton) & bajaj, retro reflective stop disc 600 mm dia red disc from minimum 20 swg gi sheet with a vertical stiffening "v' or 'u' bend in the middle having red reflector buttons/luminous stripes facing the road tr

State Government

CTN :43085670

27 Jan, 2026 NA

Gandhinagar - Gujarat

Tender For corrigendum : supply of various size & types of rtds for 3x210 mw unit 3,4 & 5 at gandhinagar tps. - duplex rtd pt-100 as per gtps drg no ext-inst-00434 for unit no 3 and 4 id fd pa fan and motor and coal mill motor de nde bearing temperature measurement system., solid sintered tungustan carbide thermowell, length 325 mm, process conn. m 33 x 2 (m), inst conn. 1/2 inch bsp (f) for coal mill out let temperature as per drg. no.gtps/ext- imd-ii -00713, rtd duplex 3 wire pt-100 for coal mill outlet temp, od 6 mm,ss 316 sheath material insulation compact filled mgo insertion length 450 mm end connection 1/2 inch bsp head die cast aluminium ip 65.ext, pipe 150 mm., rtd, pt-100, duplex, 3 wire mineral insulated (compact mgo filled) without head (head less), sheath dia: 6 mm, sheath length: 60 mm., rtd, pt-100, duplex, 3 wire mineral insulated (compact mgo filled) without head (head less), sheath dia: 10 mm, sheath length: 300 mm straight., rtd, pt-100, duplex, 3 wire mineral insulated (compact mgo filled) without head (head less), sheath dia: 12 mm, sheath length: 100 mm straight, cable length: 15 meters., rtd, pt-100, duplex, 3 wire mineral insulated (compact mgo filled) without head (head less), sheath dia: 8 mm, sheath length: 25 mm., rtd, pt-100, duplex, 3 wire mineral insulated (compact mgo filled) without head (head less), sheath dia: 12 mm, sheath length: 250 mm straight, cable length: 20 meters., rtd, pt-100, duplex, 3 wire mineral insulated (compact mgo filled) without head (head less), sheath dia: 12 mm, sheath length: 250 mm straight, cable length: 10 meters., rtd, pt-100, duplex, 3 wire mineral insulated (compact mgo filled) without head (head less), sheath dia: 12 mm, sheath length: 350 mm straight, cable length: 10 meters., rtd, pt-100, duplex, 3 wire mineral insulated (compact mgo filled) without head (head less), sheath dia: 08 mm, sheath length: 250 mm straight, cable length: 10 meters., headless rtd(pt-100type) for f.d.fan of gtps unit no 5-d.e. /n.d.e. bearing temperature measurement,sheath dia. 8 mm, sheath length: 180 mm, process connection (male): dia:17.5mm thread:1.0 mm pitch 15 mm with adjustable sewage lock type., headless rtd (pt-100 type) for turbine,boiler and balance of plant services temp measurement,sheath dia. 5 mm, sheath length: 300 mm, process conn: -18 od x thread 1.0 mm pitch length 12mm with adj.sewage lock type, headless rtd (pt-100 type)for c/m o/l shaft low radial brg, warm shaft radial brg, o/l shaft brg temperature measurement, sheath dia.5.5 mm, sheath length: 432 mm,process connection:1/2 inch bsp (m) thread 14g with adj. sewage lock type, headless rtd for ce pump journal brg, cw pump thrust / general brg temp measurement, sheath dia.4.5mm,process onnection:1/2 inch bsp (m) with adjustable sewage lock type,sheath length:200 mm,, rtd pt-100 with thermowel element : is:2848,duplex /ungrounded t/w construction straight , material : solid tungusten carbide process conne: screwed m 33 x 2, ss316 t/w insertion lenth ( l1) 325 mm t/w od :22 mm, rtd (pt-100 type) for coal mill of gtps unit no 5-upper radial bearing temperature measurement, and dimension and material of construction as per drg. no: gtps / ext / c and i / 00775., head with plug and socket type temperature element pt-100 rtd for bearing temperature of high speed shaft coupling side, insertion length 170 mm., head with plug and socket type temperature element pt-100 rtd for lower bearing temperature of low speed shaft, range: 0-100 dec c, insertion length 290 mm., head with plug and socket type temperature element pt-100 rtd for lower bearing temperature of medium speed shaft, range: 0-100 dec c, insertion length 365 mm., head with plug and socket type temperature element pt-100 rtd for upper bearing temperature of medium speed shaft, range: 0-100 dec c, insertion length 700 mm., head with plug and socket type temperature element pt-100 rtd for upper bearing temperature of low speed shaft, range: 0-100 dec c, insertion length

corporations/Associations/Others

CTN :42941512

22 Jan, 2026 NA

Anpara - Uttar Pradesh

Tender For corrigendum : supply of misc items for ffsd-i & ahd btps anpara - ht hex head full thread nut & bolt ; m16x65 mm,, ht hex head full thread nut & bolt ; m16x70 mm,, hthh bolt with nut & washer , half threaded m16x90, hex hd m18x70; ht 10.9 grade, ms bolt & nut size 20x70 mm, ht hex bolt & nut 20x80fth, fluidizing pads for esp hoppers, size: 374 mm x 374 mm, no. of holes: 16, hole dia: 12 mm material: nomex (as per sample), perforated ms plate, size: 374 mm x 374 mm, having 4.76 mm dia holes at 7.14 mm pitch giving 40.5 % open area plate thickness: 1.6mm, no. of mounting holes: 16, hole dia: 12 mm (as per sample), submersible pump, make-kirloskar, model-eterna 1100 cw+ specification : power supply-415v, 3phaseacpower rating-1.1kw/1.5hpmax. solid handling size (mm) - 24minimum submergence (mm) - 460suction - from bottomsize discharge outlet (mm) - 50max. amb. temperature - 40 degree cdischarge 366 to 84 lpmtotal head - 6 to 14 mtrsspeed (nominal) 2800 rpm, discharge tube with fmb(foam making branch) for mechanical foam extinguisher 50 ltr. discharge tube shall be braided rubber plasticof 3.5 mtr length & 12.5 mm internal dia. fitted with plastic fmb (is-7328) as per is-13386 the discharge hose shall have bu stingpressure of not less than 50 kg/cm . (as per sample), discharge tube for dcp(dry chemical powder) 05 kg extinguisher (plunger type). made of pvc. one end thread is provided to fit withdcp fire extinguisher (plunger type) capacity 5 kg and other end to discharge powder.(as per sample), discharge tube washer for dcp(dry chemical powder) 05 kg extinguisher (plunger type). made of rubber suitable to be fitted withdischarge tube of dcp fire extinguisher (plunger type) capacity 05 kg.(as per sample), discharge tube for dcp(dry chemical powder) 10 kg extinguisher (plunger type). made of pvc. one end thread is provided to fit withdcp fire extinguisher (plunger type) capacity 10 kg and other end to discharge powder.(as per sample), discharge tube washer for dcp(dry chemical powder) 10 kg extinguisher (plunger type). made of rubber suitable to be fitted withdischarge tube of dcp fire extinguisher (plunger type) capacity 10 kg.(as per sample), cap rubber washer for dcp(dry chemical powder) 75 kg extinguishers.made of rubber, suitable to fit in the cap assembly of dcpfire extinguisher capacity 75 kg.(as per sample), discharge tube for dcp 75 kg extinguishers. discharge tube/hose with nozzle squeeze grip aluminum lengths -5 mtr. suitable fordcp type fire extinguisher capacity-75 kg.(as per sample), washer for copper connecting tube 75kg dcp(dry chemical powder) extinguisher. made of rubber. suitable for fitting with copperconne cting tube of dcp 75 kg extinguisher.(as per sample), discharge tube for 9 ltr water type extinguishers (squeeze grip type). pvc braided tube/hose of length 400 mm. suitable for fittingwithin the thread of squeeze grip assembly of water type fire extinguisher capacity 9 litre (squeeze grip type).(as per sample), discharge tube washer for 9 ltr water type extinguishers (squeeze type). made of rubber. suitable to be fitted with discharge tube/hoseof water type fire extinguisher (squeeze grip type) capacity 09 litre.(as per sample), port tube for 9 ltr water type extinguishers (squeeze grip type). port tube/actuator should be made of aluminium. suitable to fit insidecap assembly of water type fire extinguisher capacity 9 litre (squeeze grip type) for release of water when activated. as per sample), siphon tube for 9 ltr water type extinguishers (squeeze grip type). siphon tube suitable for 9 ltr. water type extinguishers (squeezegrip type).(as per sample), cap assembly for 9ltr water type extinguishers (squeeze grip type). it should include a brass forged valve and a squeeze grip foractivation to facilitate the discharge of water. suitable to be fitted in 9l water type extinguishers (squeeze grip type).(as per sample), cap assembly washer for for 9 ltr water type extinguishers (squeeze

corporations/Associations/Others

CTN :43524606

20 Jan, 2026 3.00 Lacs

Ahmedabad - Gujarat

Tender For supplying jcb machine, dewatering pump, spindel, check nut and other material and machinery maintainance work of drainage / water deparment in thakkarnagar ward of north zone. (arc)

Corporations And Associations And Others

CTN :43499288

15 Jan, 2026 2.98 Lacs

Delhi - Delhi

Tender For supply of machinery/tools for various parks at sarita vihar in ward no. 187, central zone - brush cutterengine: single cylinder, 2 stroke, aircooled onlyengine displacement: 40.2ccpower output: 2kw/2.7hpmax output shaft speed at cutting attachment: should be minimum 9000 rpmcarburetor: diaphragm with compensator technology.fuel tank capacity: minimum 600 ml.weight( dry,without cutting attachment & deflector): should not be more than 7.5 kgclutch: centrifugal type, clutch shoe support base & lining metal only.multi function handle: should have acceleration ,on/off switch at right handle.brushcutter harness: should be double shoulder harness only.anti vibration system: must have 4- point aniti vibration system.vibration level in m/s2 at right handle : should not be more than 2.5 m/s2sound pressure level db(a): should not be more than 105 db(a)drive shaft design: must have drive shaft ends square design type only.certification : must have valid en certificaton, petrol operated chain sawengine : single cylinder, 2 stroke, aircooled onlydisplacement: 45.4ccpower output : 2.3kw. 3.0 hp max.engine speed (with guide bar & chain ): at least 12500 rpmcarburetor: diaphragm type & compensator technology.fuel tank capacity: should be minimum 450 ml.dry weight( without cutting attachment ): should not be more than 5.0 kgclutch: clutch shoe linining metal only.guide bar design: should be rollomatic type.guide bar length: guide bar length must have 50 cm/20" inch. guide bar and chain: should have same manufacture only.chain type: every drive link require groove & small oil receiver hole for better lubrication. 0.325 inch pitch & 1.6 mm thickness only.chain lubrication system: fully automatic ,speed controlled rotary oil pumpchain oil tank capacity: should be minimum 200 ml.oil pump drive: should have direct drive from crankshaft & oil pump flow adjustable.master lever control: must have all operation in one hand, chock,throttle, acceleration,switch off.guaranteed sound power level: should not be more than115 db(a)maximum chain velocity to iso 11681: should be minimum 28 m/scertification: product should have valid dplf certificate with test standard en iso 11681., tree prunersupply of telescopic pole pruner:-specification:- pole length incuding blade: 6.5m blade material: hardened & tempered high carbon steel .the head of the blade shall have a hooked tip useful for cutting twigs saw blade shape: hooked type curved saw blade type & no of cutting teeth :tripple grounded 86 teeth blade length : 15"-16" pole type: light weight telescopic tubular aluminium alloy extendable pole no of positions for pole height adjustment : 10 positions locking mechanism : ergonomicvally designed two way locking mechanism total working length : max 219"(6623 mm), min 103" (3103mm) branch cutting capacity: 200mm max, lawn mowersupply of lawn mower:-specification:- type of machine walk behind lawn mowerspower source petrol enginestart type recoil / pull startspeed control variable speeddrive type all wheel driveblade style rotary typeblade engagement electromagneticcut width (mm) 500 to 524minimum cut height 1 millimetermaximum cut height 26 millimeterblades metallicnumber of blades 1number of positions for cut - height adjustment 2number of levers for cut - height adjustment single levernumber of wheels 4front wheel size 200 millimeterrear wheel size 200 millimeterwheel tyres pneumaticif yes, grass catcher / collector / bag volume 88 liter"engine power rating (watt)" 4000 to 4999engine fuel tank capacity - 1 ltr., lopperanvil tree branch lopper lade material - high carbon steel with hard surface treatment, overall length - not less than 914 mm handle material - similar materil as per requirement, weight - 1.5 kg., cutting dia - not less than 38mm

CTN :42842817

20 Jan, 2026 16.90 Lacs

Chhabra - Rajasthan

Tender For corrigendum : supply of spare/accessories items of two nos. multi-purpose fire tender(rj-28ea-0956 and rj-28- ea-0957)against tn-sc-638/2025-26(mm) - high pressure hose reel with 60mm lg x 19 mm ( ) with fog gun and spray type, low pressure hose reel with 19 mm x 50 mm long hose with duel purpose shut off nozzle., extension ladder 10.5 meter, delivery hose 63 mm rubber lined in 30 m length (type b of is 636/79/5) complete with instantaneous coupling., long line 50 mm circumference 30 m long as per is 1084., short line 50 mm circumference 15m length as per is 1084., protective clothing for fireman complete with golves, boots, helmets with suitable face shield mad out of material capable of reflecting at least 95% of radiant heat temperature around 1500 to 2000 degree celsius and also afford some protective against direct flame. the suit will be of sufficient size to accommodate a breathing apparatus to users (item should be packed in hard body box)., fire hook, fire man axe, sledge hammer, carpenter saw, pick axe, celling hook, crow bar made of carbon steel, self contained breathing apparatus (45 min duration compressed air type) complete with spare cylinder & tool kit), dividing breeching, collecting breeching, pvc suction hose heavy duty complete with copper alloy round threaded couplings to suit the pump inlet - 2.5m long., suction strainer for item 2, basket strainer suitable for item 4 , is : 3582, dividing breaching with control arrangement as per is : 5131, collecting breaching as is : 905, hose bandages rubberized is : 5612, hose clamps is : 5612, water curtain nozzle made of m .s .plate with g . m instantaneous connection, branch pipe short ( chromium plated) is : 903, a set nozzle of sizes 12 mm , 16 mm , 20mm , 25 mm and 32 mm ( two each ) ( see is : 903 - 1975 * t ), adapter for 100mm suction female thread and 63mm male instantaneous, adaptor double female instantaneous pattern 63mm ., adaptor double male instantaneous pattern 63mm, hand lamp ( 4cells ), rubber gloves 33kv 1 pair, fire beater, foam pick up tube, rubber gloves as per is 4770 - 1991 for 5000 volts, leather gloves is 6994 1977, jack hydraulic for 20 ton capacity with handle, hand controlled branch for 63 mm size hose coupling, hand held fast action select flow nozzle :-the selectable flow rate multipurpose nozzle should have a multiple flow setting. this product be of light in weight and easy to handle. weight of the nozzle should not be more than 2 kg. the calibrated flow rates are easily selectable through an selection ring. the stream patterns should be changed by rotating the diffuser head ring. nozzle should be having pistol grip, shut off ball valve opening and made of aluminum alloy., bolt cutter 600mm long, shovel with handle, minimum 12v halogen fog & spot lamps, hose ramp

CTN :43521661

24 Jan, 2026 NA

Pondicherry - Pondicherry

Tender For supply of dental equipments and instruments d d - chairside cadcam , confocal microscopy , automated cell imaging system , ten-headed teaching system , porcelain furnace porcelain furnace programmable with vacuum pump and instrument kit and material kit for all ceramic , claro nav system navigation system , porcelain furnace programmable with vacuum pump and instrument kit and material kit for metal ceramic , triple wavelength laser , harmonic surgical knife , surgical endodontic microscope , dental casting machine motorised , casting machine , ergonomic dental chair beach technique , software for cephalometrics model analysis , cad cam digital 3d printer , cad software , t-scan novus , surgical instruments , preclinical prosthetics working table , rmo 660xp multipurpose welder with ce safety standards uk model plug with 220 250v , ventilator , portable dental chair , dental implant advanced kit sinus lift kit , florida pressure sensitive probe , saf file with rdt handpiece , orthodontic mobile instrument carts , intraoral scanner , de-waxing unit , ultrasonic scalers , unit mount scaler , fully adjustable articulator , implant kit with both surgical and prosthetic components , intubation endoscope fibreoptic , tmj arthroscope , operating microscope ) /bid number : gem/2026/b/7072661 * /dated: 09-01-2026 & & / bid document 1 / 35

Horticulture Pump Repair Tenders

By Cities

By States

By Agencies

By Ownerships

By Sectors